Refrigerator Solar Battery Runtime Calculator

Use this refrigerator solar battery runtime calculator to estimate how long stored battery energy can power a fridge. Enter your battery capacity and refrigerator demand, then compare the stated assumptions in Simple and Advanced modes.

The estimate accounts for an illustrative or entered compressor duty cycle and selected energy losses. It includes no incoming solar generation and does not predict food temperature or guarantee inverter compatibility.

Jump to the refrigerator runtime calculator · Read calculation questions · Calculator methodology and limitations

Refrigerator Solar Battery Runtime Calculator
Off-Grid Refrigerator Runtime

Refrigerator Runtime Calculator (Simple & Advanced)

Estimate how long your fridge may keep food cold on solar — accounting for duty cycle, ambient temperature, age, depth of discharge, reserve cutoff, and inverter losses. Results are planning estimates, not guarantees.

~35%Avg Duty Cycle
Measured WhPreferred input
RuntimeCalculated below
Duty cycleUse measured data
Planning note: Runtime depends on the exact refrigerator model, thermostat setting, ambient heat, door openings, battery condition, inverter cutoff, and food load. Use this as a sizing estimate and keep a thermometer inside the fridge/freezer during outages.
Estimated Runtime
—
at the stated average duty
Daily Wh Used
—
average 24-hr draw
Avg Battery Load
—
after conversion losses
Days at Half Duty
—
illustrative half compressor duty
Quick Start: Pick Your Fridge

Ah mode assumes 12.8V: capacity Wh = Ah × 12.8V. Advanced duty is used exactly as entered; use measured average watts with 100% duty if available. Other Loads use the same conversion path as the fridge. Battery-side draw = (running watts × duty + other watts) ÷ conversion efficiency ÷ (1 − additional loss). Additional reserve is a fraction of DoD-limited energy, not a second absolute state-of-charge cutoff. Half-duty comparison halves compressor on-time only; other loads remain unchanged. Advanced temperature and door-opening fields are informational and do not alter entered duty.

⏱️
Runtime
—
at the stated average duty
⚡
Energy used
—
over 24 hrs
💵
Grid Energy Equivalent
—
illustrative $0.15/kWh; not a bill

Energy Breakdown

Fridge running watts—
Duty cycle (compressor on time)—
Average compressor load—
Conversion losses (incl. system)—
Total real draw—
Battery health derate—
Reserve / cutoff kept unused—
Daily kWh—

Battery Size Comparison

BatteryCapacityUsableRuntime

System Notes

How we calculated this Enable JavaScript to see the calculation from your inputs.
💡 You’re well-sized — this fridge will run nearly 2 full days off-grid on a single charge.
Try a different size →

How to use the refrigerator solar battery runtime calculator

  1. Enter battery energy in Wh. If your specification is in Ah, multiply Ah by nominal voltage first. The Simple-mode Ah shortcut assumes 12.8V.
  2. Choose a Simple-mode fridge profile for an illustrative estimate, or use Advanced mode for measured running watts and duty cycle.
  3. If you measure average total fridge watts, enter that power with 100% duty. Do not apply a duty-cycle reduction twice. Include uncounted fan, defrost, standby and other loads separately.
  4. Enter battery health, depth of discharge, reserve, inverter efficiency and additional losses as applicable. Avoid counting the same loss twice.
  5. Compare the estimated hours with your required backup period. Check continuous and startup power against the equipment manufacturer specifications separately.

Refrigerator battery runtime formula

Usable battery Wh = nominal Wh × health × DoD × (1 − additional reserve).

Battery-side watts = (fridge running watts × duty fraction + other load watts) ÷ inverter efficiency ÷ (1 − additional loss).

Runtime hours = usable battery Wh ÷ battery-side watts. Fractions are entered as decimals in this explanation: 90% = 0.90. Additional reserve here reduces the DoD-limited energy; it is not an independent state-of-charge cutoff.

Worked example: 1,000Wh battery and 150W refrigerator

Assume 100% battery health, 80% DoD, no additional reserve, 90% inverter efficiency, 10% additional loss, 35% compressor duty and no other loads.

  • Average appliance power: 150 × 0.35 = 52.5W.
  • Usable battery energy before conversion: 1,000 × 0.80 = 800Wh.
  • Battery-side power: 52.5 ÷ 0.90 ÷ 0.90 = 64.81W.
  • Estimated elapsed runtime: 800 ÷ 64.81 = approximately 12.34 hours.

The 12.34-hour result already includes compressor cycling. It must not be extended again to represent a full day. Actual results depend on measured demand, battery condition, operating temperature and equipment limits.

Calculate refrigerator battery runtime from kWh per day

A representative energy-meter reading over a full day can include compressor cycling, fans and defrost. Convert appliance energy to average load: average watts = measured kWh/day × 1,000 ÷ 24. For example, 1.2kWh/day equals 50W average. In Advanced mode, enter 50W and 100% duty rather than applying compressor duty a second time. Add other loads only if they are outside the measurement.

With a 1,000Wh battery, full health, the illustrative LiFePO4 90% DoD preset, no additional reserve, 90% inverter efficiency and 10% additional loss, that 50W average demand gives 900 × 0.90 × 0.90 ÷ 50 = 14.58 hours. Measuring at the battery side instead requires different loss accounting; do not apply conversion losses twice.

How long will a 12V 100Ah battery run a refrigerator?

At nominal 12V, 100Ah means 1,200Wh. Under the same 50W average load and loss assumptions, estimated runtime is 17.50 hours. Enter 1,200Wh explicitly for this 12V example: this tool’s Simple Ah shortcut assumes 12.8V and would use 1,280Wh. Neither energy estimate checks compressor startup, battery current capability or food-storage temperature.

To plan replacement energy, use the solar panels to run a refrigerator calculator separately. A battery-only duration does not establish that a solar array can sustain the load through every season.

Planning solar recharge separately

This tool estimates runtime from stored energy only. Compare daily battery-side demand with seasonal solar production using the Solar Panel Output Calculator. Use the refrigerator solar panel calculator for a panel-count scenario and the Battery Bank Size Calculator for storage planning. These tools provide estimates under their stated assumptions.

Recommended Next Steps

Continue Planning After Fridge Runtime Estimate

Refrigerators are continuous-cycle loads and one of the most important appliances in an off-grid system. After estimating runtime, the next step is confirming battery size, evaluating full system runtime, checking recharge time, and validating your overall setup.

Refrigerator Runtime: Calculation Questions

Should I use running watts or average watts?

Running watts multiplied by duty fraction estimates average compressor demand. Include fan, standby and defrost demand separately. If you have a measurement of average total power, use that number with 100% duty rather than applying duty again.

How are losses applied?

Battery-side watts = (running watts × duty + other load watts) ÷ conversion efficiency ÷ (1 − additional loss). Usable battery Wh = nominal Wh × health × DoD × (1 − additional reserve). Runtime hours = usable Wh ÷ battery-side watts. Avoid including the same loss in more than one input.

Why can Simple and Advanced results differ?

Simple mode estimates duty from illustrative equipment and temperature profiles. Advanced mode uses the duty you enter without applying temperature or door-opening multipliers. Measured energy use is a better basis for a particular fridge.

How do Ah and Wh compare?

Wh = Ah × nominal battery voltage. This tool’s Simple Ah shortcut assumes 12.8V. Use the Wh input for other battery voltages. Manufacturer-specific capacity limits and discharge curves are not modeled.

Can a panel make the fridge run indefinitely?

A panel rating alone cannot establish that. Compare battery-side daily energy demand with seasonal solar production and storage requirements separately. This runtime calculation includes no incoming solar energy and does not verify inverter compatibility or predict food temperature.

Refrigerator energy-use reference

Use measured daily consumption or the refrigerator’s EnergyGuide information where available: actual compressor duty cycle changes with ambient temperature, settings and door opening. See the U.S. Department of Energy’s residential refrigerator energy-use guidance. Also verify inverter startup surge and battery discharge limits.

Equipment for Refrigerator Battery Runtime

Measure real refrigerator demand, plan appropriate battery and inverter capacity, and monitor food-storage temperatures.

P3 Kill A Watt P4400 Electricity Usage Monitor

Measure cumulative AC refrigerator energy use over at least a full day, including compressor cycling, to improve your runtime estimate. Intended for compatible 115V AC outlets and appliances.

Click for the latest price.

LiTime 12V 100Ah LiFePO4 Battery

A nominal 12.8V, 100Ah battery option for off-grid storage planning. Verify BMS discharge limits, charging conditions, protection, system voltage and required capacity before purchase.

Click for the latest price.

Renogy 1000W Pure Sine Wave Inverter

Converts compatible 12V DC battery power to 120V AC. Confirm the refrigerator’s continuous demand and measured compressor-start surge against inverter ratings and battery capabilities.

Click for the latest price.

AcuRite 00986M Wireless Fridge/Freezer Thermometer

Remote temperature display with two sensors to help monitor refrigerator and freezer conditions during off-grid operation or power interruptions.

Click for the latest price.

As an Amazon Associate I earn from qualifying purchases. Check electrical ratings, wiring, fusing, installation requirements and manufacturer compatibility before connecting a battery or inverter; seek a qualified electrician where appropriate. This calculator does not establish food safety—use actual temperature readings and applicable food-storage guidance.

Scroll to Top