Off Grid Living Tools drip irrigation planning banner with garden beds, emitters, water tank, cabin and illustrated results
Illustrative banner values are not a worked example. Use the calculator results below for your inputs.

Drip Irrigation Flow & Water Demand Calculator

Plan crop water demand, emitter flow, sequential irrigation zones, watering runtime and backup tank storage. Start with Simple mode or refine local conditions in Advanced mode.

Quick Answer

Daily gross irrigation water = area × max(0, ETo × crop coefficient − effective rainfall) ÷ efficiency. Divide event water by emitter flow to find runtime. For example, 100 m² at 5 mm/day and 90% efficiency needs 555.56 L/day. With 200 emitters at 2 L/hour, total flow is 400 L/hour; a 5 L/min source needs two sequential zones, each running about 83.33 minutes daily.

Calculate your drip irrigation plan

Use the full cropped bed area represented by the crop coefficient, not just the wetted spots. ETo is reference evapotranspiration from local weather data, not rainfall or direct crop demand. Enter source flow available at operating pressure after other uses. US gallons are not Imperial gallons.

Simple assumptions: Kc 1; effective rain 0; efficiency 90%; daily irrigation; 3 days of storage; 10% reserve; 90-day season. These are editable in Advanced mode.

Before installing or changing a system

This is a planning estimate, not hydraulic or agronomic approval. Confirm pressure at the farthest emitter, filter and regulator requirements, pipe friction, elevation changes and manufacturer limits. A bucket test with an open hose does not prove flow at irrigation pressure. Use suitable backflow protection where connected to drinking water; follow local requirements.

Inspect for clogged emitters and leaks, flush lines, and check actual discharge and soil moisture. Avoid ponding, runoff and root-zone saturation. Water quality, salinity leaching, fertigation, frost protection, germination and crop stress are outside this model. Adjust the plan using local crop advice and measured conditions.

Useful equipment for drip irrigation planning

Measure your supply, protect emitters and track soil moisture before expanding your drip system. Confirm fitting sizes, pressure ratings and local compatibility.

RESTMO Hose Water Flow Meter

Measures flow and volume at compatible garden-hose connections. Useful for checking supply; it does not prove flow at an emitter’s operating pressure.

Click for the latest price.

Rain Bird PRF07530S Drip Filter

Helps filter debris that can clog drip emitters. Verify filter rating, operating flow and connection sizes for your system.

Click for the latest price.

ECOWITT Soil Moisture Sensor Kit

Tracks soil-moisture changes to support watering adjustments. Check gateway requirements, sensor range and correct placement.

Click for the latest price.

Orbit B-hyve Smart Hose Faucet Timer

Schedules watering from a compatible hose faucet. Confirm connectivity, pressure range and valve requirements before ordering.

Click for the latest price.

Affiliate disclosure: As an Amazon Associate, we earn from qualifying purchases. Product links may earn us a commission at no additional cost to you.

Formulas and a checked example

Crop ET = ETo × Kc. Net irrigation depth = max(0, crop ET − effective rainfall). Gross daily volume (L) = cropped area (m²) × net depth (mm/day) ÷ (efficiency / 100). Event volume = daily volume × interval days. Seasonal volume = daily volume × season days, assuming constant weather and crop conditions.

Total emitters = plants × emitters per plant. Total flow (L/hour) = emitter count × emitter rate. Maximum emitters per zone = floor(source L/min × 60 ÷ emitter rate). Required zones = ceil(total emitters ÷ maximum emitters per zone). Emitters are distributed as evenly as possible. Every zone has the same runtime because the model assigns equal water demand per emitter.

Runtime per zone (hours) = event volume ÷ total emitter flow. Sequential watering window = runtime × zone count. Nominal tank volume = daily volume × backup days ÷ (1 − reserve / 100). Existing tank autonomy = usable tank volume ÷ daily demand. Tank sizing assumes no refill; the supply must still support each active zone.

Default example: 100 m² × 5 mm/day ÷ 0.9 = 555.56 L/day. 100 plants × 2 emitters × 2 L/hour = 400 L/hour. Source 5 L/min = 300 L/hour, allowing 150 emitters per zone. Two balanced zones of 100 emitters each draw 200 L/hour. Each applies 277.78 L in 1.3889 hours; total sequential time is 2.7778 hours. Three backup days with 10% reserve require 1,851.85 L nominal storage.

Conversions: 1 US gallon = 3.785411784 L; 1 inch = 25.4 mm; 1 ft² = 0.09290304 m². Switching units converts existing values and keeps the same physical plan. Advanced values retain their stated dimensions.

Water-saving field checks

Group crops with similar water needs. Use mulch where appropriate, repair leaks, and choose watering times that suit local restrictions and plant conditions. Observe the wetting pattern at root depth; add or reposition emitters if coverage is inadequate. More emitters increase flow but do not increase the modeled crop demand. Keep enough operating headroom for pressure variation and filter fouling.

Frequently Asked Questions

How much water does drip irrigation need?

Multiply cropped area by net crop water depth, then divide by application efficiency. One millimetre over one square metre equals one litre. The default 100 m² plot needs 555.56 L/day at ETo 5 mm/day, Kc 1 and 90% efficiency, without rainfall.

How is emitter flow calculated?

Multiply plants by emitters per plant by each emitter’s measured hourly flow. Use flow at the actual operating pressure. The calculator uses point emitters; convert tape specifications to total emitter count and equivalent per-emitter flow before using it.

Does dividing the garden into zones save water?

Zoning limits instantaneous flow. It does not reduce the calculated total water demand. Sequential zones take longer overall, assuming the same water application per emitter.

Which crop coefficient should I use?

Use a locally appropriate coefficient for the crop and growth stage from an agricultural extension service or FAO guidance. The Simple-mode value of 1 is an illustrative assumption, not a crop recommendation.

Can I water every few days instead of daily?

Advanced mode multiplies daily demand by the selected interval. That volume must fit in the root zone without runoff or deep drainage; this tool does not model soil water storage. Split cycles and check moisture at root depth.

How large should my irrigation tank be?

The nominal target is gross daily irrigation demand times backup days, divided by the usable fraction after the reserve. Add household demand separately. Refill, dead storage, rain variability and seasonal reliability need separate planning.

Next Step Links

Related Tools

Sources and model limits

The crop-demand approach follows FAO guidance on crop coefficients and evapotranspiration. See FAO irrigation water needs for rainfall accounting, and Utah State University’s drip irrigation guide for practical flow and application planning.

Reviewed 2 November 2026. One crop/area model, identical emitters, balanced zones and constant conditions are assumed. This page does not calculate pipe sizing, pressure uniformity, pump curves, refill reliability, soil water balance or a month-by-month schedule. Results are estimates rounded for display.

Scroll to Top