
Solar Battery Runtime Calculator – Estimate Battery Hours
How long will your solar battery last? Use this free solar battery runtime calculator to estimate how many hours a fully charged battery bank can power your appliances. Calculate battery runtime using stored energy, electrical consumption, battery chemistry, battery health and inverter efficiency.
Whether you use a 12V, 24V or 48V battery system, this calculator helps estimate operating time for off-grid homes, cabins, RVs and backup power systems. Compare different battery capacities and appliance loads to understand how changes in electricity demand affect available runtime.
Calculate Battery Runtime in Simple or Advanced Mode
Simple Mode estimates runtime from nominal battery capacity, battery chemistry, battery health, inverter efficiency and a continuous or average electrical load.
Advanced Mode calculates average demand over 24 hours using individual appliance wattages and operating hours. It also accounts for applicable AC standby consumption and battery-side inverter idle demand.
How Is Solar Battery Runtime Calculated?
Battery runtime depends on the amount of usable stored energy and the power consumed by connected appliances. A basic energy estimate divides usable battery watt-hours by average electrical demand in watts.
Basic battery runtime formula:
Runtime (hours) = Usable Battery Energy (Wh) ÷ Average Battery-Side Power Demand (W)
Usable energy may be lower than nominal battery capacity because of depth-of-discharge limits, battery condition and other losses. AC appliance demand must also account for inverter efficiency and applicable inverter idle consumption. Actual runtime depends on equipment specifications and operating conditions.
Important: This is a battery-only runtime estimate. The calculator does not include incoming solar generation or battery charging while appliances operate. It does not simulate an hourly load schedule or verify that the battery and inverter can safely deliver the required power.
Continue Your Battery and Solar Planning
For a partially charged battery or additional reserve assumptions, use the Solar Battery Discharge Calculator .
To calculate storage requirements from your daily electricity demand and desired backup period, use the Battery Bank Size Calculator .
For portable power stations and solar generators, compare your results with the Solar Generator Runtime Calculator .
All results are planning estimates. Keep battery capacity, conversion efficiency, load assumptions and reserve settings consistent when comparing calculators.
How Long Will a Solar Battery Run Your Appliances?
A solar battery’s operating time depends on its usable energy capacity and the electrical demand of connected appliances. Larger batteries generally provide longer runtime when the total load remains unchanged.
Example: 2,000Wh Battery Running a 200W Load
A 2,000Wh battery supplying a constant 200W load provides an ideal maximum of:
2,000Wh ÷ 200W = 10 hours
With an illustrative 90% usable depth of discharge, 100% battery health and 90% inverter efficiency:
2,000 × 0.90 × 0.90 ÷ 200 = 8.1 hours
Estimated battery runtime: 8.1 hours under these assumptions, with no additional loads or inverter idle consumption.
What Affects Battery Runtime?
- Nominal battery energy and voltage
- Battery chemistry and usable depth of discharge
- Battery age, condition and health
- Appliance wattage and simultaneous loads
- Inverter efficiency and idle consumption
- Actual operating hours and load variations
How Solar Battery Runtime Is Calculated
Solar battery runtime is calculated by comparing the usable energy stored in the battery with the power draw of the appliances connected to it. The more usable watt-hours a battery has, and the lower the electrical load, the longer the battery can keep supplying power.
The calculator assumes a full starting charge. Chemistry selects an illustrative depth-of-discharge fraction; health reduces nameplate capacity, and inverter efficiency converts modeled battery-side energy into AC-equivalent delivered energy. These preset fractions are not manufacturer operating limits or guarantees of battery life.
Solar Battery Runtime Formula
Runtime (hours) = AC-equivalent usable Wh ÷ equivalent average AC draw W. Usable Wh = nominal Wh × health × (1 − discharge-rate loss) × (1 − cold loss) × DoD × inverter efficiency.
Simple Mode uses the entered average load directly, with zero added standby or idle draw and no cold reduction. Advanced Mode uses appliance daily Wh ÷ 24, plus AC standby watts, plus battery-side idle watts × inverter efficiency. This is equivalent to dividing battery-side usable Wh by AC demand ÷ efficiency plus DC idle demand.
For the worked 2,000Wh example below, Advanced Mode uses an 80% DoD override, new health, 90% inverter efficiency, one 200W appliance for 24 hours/day, zero standby and idle draw, and no optional derating. It gives 1,440Wh delivered and 7.2 hours. This differs from the Simple Mode 90% LiFePO4 default.
Key Factors That Affect Battery Runtime
- Total battery capacity in watt-hours
- Battery depth of discharge
- Inverter efficiency
- Total appliance wattage running at the same time
- Battery age, temperature, and real-world operating conditions
How long will your battery realistically last?
Enter your bank size, pick a chemistry, and add the appliances you plan to run. The model applies your chosen depth of discharge, inverter efficiency and optional illustrative temperature and discharge-rate losses. Actual runtime depends on your battery and equipment specifications.
Configure your battery
Start with a preset or build your own setup
Enter a positive capacity and load. In Ah mode supply positive voltage and Ah. Efficiency and optional DoD must be above 0 and at most 100%; appliance hours must be 0–24; watts cannot be negative. Complete active fields.
Battery-only energy estimate: no solar charging is credited. Advanced appliance use is averaged over 24 hours, so short backup windows may differ. Appliance/standby watts are AC-side; inverter idle is battery-side. Equivalent average AC draw = appliance watts + standby watts + idle watts × efficiency. Do not add idle separately if it is already included in a measured efficiency. Cold and discharge-rate reductions are illustrative assumptions, not a battery-specific discharge curve.
Your battery runtime
Based on your configuration and loads
Battery drain timeline
— hrs remainingStart powering loads to see your drain curve.
LiFePO4 specs
Flagship chemistryRuntime at different total AC-equivalent draws
| Scenario | Load | Runtime | Visual |
|---|
Why this runtime
Run the calculation to see the breakdown.
Next step to extend runtime
—
Helpful equipment
Equipment to Check Battery Runtime
These examples help compare battery storage, monitoring and appliance load. They are not automatically matched to your calculator results. Confirm manufacturer ratings and electrical compatibility before choosing equipment.
LiTime LiFePO4 Deep-Cycle Battery
Compare usable energy and discharge ratings for battery runtime planning.
Click for the latest price.Renogy 500A Battery Monitor
Observe current and remaining energy to compare measured results with estimates.
Click for the latest price.P3 Kill A Watt Electricity Usage Monitor
Measure actual AC appliance draw to refine runtime assumptions.
Click for the latest price.Renogy 3000W Pure Sine Wave Inverter
Compare inverter power and efficiency for AC appliances supported by a battery.
Click for the latest price.This section contains affiliate links. We may earn a commission.
Continue Planning After Runtime Estimation
After a runtime estimate, compare recharge energy, storage size, solar generation and full-system demand separately. These tools use different assumptions and do not validate an installation.
Solar Battery Charge Time Calculator
Calculate how long it takes to recharge your battery after use.
Battery Bank Size Calculator
Estimate nominal storage for daily demand and backup days.
Solar Panel Output Calculator
Explore solar production under location and loss assumptions.
Complete Solar System Calculator
Compare a separate full-system energy-sizing scenario.
Example Solar Battery Runtime Calculation
Reproduce this example in Advanced Mode: select Wh capacity, enter 2,000Wh, LiFePO4 and new health, set DoD override to 80%, inverter efficiency to 90%, temperature to 72°F, and standby and inverter idle watts to zero. Use one 200W appliance for 24 hours/day; set other rows to zero or remove them. Turn off cold derating. No incoming solar or partial starting-charge setting is included.
Example Battery System
- Battery capacity: 2,000 Wh
- Depth of discharge: 80%
- Inverter efficiency: 90%
- Connected appliance load: 200 watts
Step-by-Step Calculation
1. Calculate usable battery capacity:
2,000 Wh × 80% = 1,600 Wh
2. Account for inverter efficiency:
1,600 Wh × 90% = 1,440 Wh of AC-equivalent delivered energy
The model gives 7.2 hours, or 7h 12m. If that same 200W appliance runs only 6 hours/day, its 24-hour average is 50W and the model gives 28.8 energy-equivalent hours (1.2 days). That does not mean it can run continuously for 28.8 hours at 200W; a short outage can follow a different schedule.
Estimated Battery Runtime
For this example setup:
- Usable battery energy: 1,440 Wh
- Appliance power: 200 watts
- Estimated runtime: about 7.2 hours
This example shows why both battery size and appliance wattage strongly influence how long a solar battery system can supply power.
Understanding Your Solar Battery Runtime Results
Results describe an energy-only scenario from full charge. They do not confirm inverter running or surge capability, battery/BMS current limits, wiring, actual voltage cutoff, or solar recovery. Advanced runtime is based on a repeated 24-hour average, so it may not represent a particular short backup window.
Battery Runtime
This value shows the estimated number of hours your battery can power the selected load before reaching the allowed discharge level.
Usable Energy
“Usable” in this tool is after health, enabled capacity adjustments, DoD and inverter efficiency. It is AC-equivalent energy, unlike the battery-side “Usable” display in the separate Discharge Calculator. Compare the energy boundary as well as the number.
Load Impact
The higher the appliance wattage, the faster the battery energy is consumed. Lower power devices allow the battery system to run for much longer periods.
Examples With Explicit Energy Assumptions
- With 2,000Wh, full/new LiFePO4, 90% DoD and 90% inverter efficiency: 100W continuous gives 16.2 hours
- With the same assumptions: 300W continuous gives 5.4 hours
- With the same assumptions: 1,000W continuous gives 1.62 hours; equipment power limits remain unchecked
- Small electronics often run many hours longer than high-power appliances
How to Use the Solar Battery Runtime Calculator
Enter nominal battery capacity and measured demand where available. Do not enter capacity already reduced for reserve and conversion losses unless you adjust the other factors to avoid counting the same reduction twice.
Enter Battery Capacity
Select Wh/kWh or explicitly select the voltage × Ah capacity method. In Simple Mode the unit selector converts Wh and kWh; Advanced capacity is entered in Wh. Use the actual nominal voltage when converting Ah.
Add Appliance Load
Simple Mode uses your entered average watts. Advanced Mode sums each appliance’s watts × hours/day and divides by 24. Enter realistic on-hours, not both duty-averaged watts and reduced operating hours for the same cycling load.
Set Reserve, Losses and Idle Demand
Chemistry supplies an illustrative DoD default; Advanced Mode accepts a positive override up to 100%. Enter inverter efficiency and health. Add AC-side standby and battery-side inverter idle separately, avoiding double counting. Simple Mode fixes temperature at 72°F. Advanced cold mode applies a fixed reduction when enabled, and temperatures below 40°F force it on even if unchecked.
Review Runtime Estimate
Click Calculate runtime to inspect hours, energy and comparison outputs. Use the model as an estimate; the timeline and “days” are energy equivalents, not a voltage trace, solar forecast or equipment-compatibility check. Cold and discharge-rate reductions are illustrative, not manufacturer-calibrated discharge curves.
Expert Tips for Improving Solar Battery Runtime
Solar battery runtime depends on usable battery capacity, electrical consumption and system efficiency. Reducing unnecessary loads, selecting efficient appliances and managing battery storage can extend operating time in off-grid homes, cabins, RVs and backup power systems.
Reduce High-Wattage Loads
Electric heaters, microwaves, coffee makers and air conditioners can place significant demands on a battery bank. Reducing their operating time or avoiding simultaneous use can extend battery runtime and reduce peak inverter demand.
Use Energy-Efficient Appliances
Choose appliances with lower measured energy consumption where practical. Efficient refrigerators, LED lighting and low-power electronics can reduce daily battery demand. Compare actual watt-hours consumed rather than relying only on appliance wattage ratings.
Increase Battery Storage Capacity
Increasing usable battery capacity can extend runtime when electrical demand remains unchanged. Additional batteries must be compatible with the existing system, including voltage, battery chemistry, battery management, wiring and charging equipment.
Improve Solar Charging Capacity
Increasing usable solar production can help replenish battery energy during daylight hours. However, charging performance depends on sunlight, charge-controller limits, battery acceptance rates and simultaneous electrical loads. Additional panels do not automatically increase charging speed.
Practical Solar Battery Planning Tip
Reduce unnecessary electricity consumption before increasing battery capacity. Lower daily energy demand may reduce the storage and solar generation capacity required to meet your needs.
Start by measuring appliance consumption, identifying high-demand equipment and determining which loads must operate during an outage or overnight. Then calculate the battery capacity needed for your desired backup duration.
Remember that battery runtime and solar recharge are separate calculations. A battery may provide sufficient overnight energy while the solar array remains too small to replenish that energy during periods of reduced sunlight.
Electrical safety: Before increasing battery capacity or installing additional solar panels, verify equipment ratings, charging limits, battery discharge capability, wiring protection and applicable installation requirements. Battery runtime estimates do not establish that a system is electrically compatible or safe to operate.
Solar Battery Runtime Comparison Guide
How long will a 2,000Wh solar battery run different appliances? The following comparison uses an illustrative 2,000Wh LiFePO4 battery with 90% depth of discharge, 100% battery health and 90% inverter efficiency. No additional standby loads, inverter idle demand or cold-weather losses are included.
Usable battery energy:
2,000Wh × 0.90 × 0.90 = 1,620Wh
Estimated runtime is calculated by dividing the available 1,620Wh by each appliance’s electrical demand. These examples use constant power consumption for comparison.
| Appliance | Electrical Power | Estimated Runtime | Usage Example |
|---|---|---|---|
| LED Light | 10 W | 162 hours | Cabin and RV lighting |
| Laptop | 50 W | 32.4 hours | Remote work and electronics |
| Television | 100 W | 16.2 hours | Entertainment and media |
| Refrigerator | 150–200 W while running | 8.1–10.8 hours* | Compressor-running comparison |
| Microwave | 1,000 W input | 1.62 hours** | Theoretical continuous-load comparison |
| Air Conditioner | 1,500 W while running | 1.08 hours** | Theoretical continuous-load comparison |
Important Runtime Limitations
* Refrigerator runtime: Refrigerators normally cycle on and off. The example assumes the compressor runs continuously at the stated wattage. Actual elapsed runtime depends on compressor duty cycle, ambient temperature, insulation, door openings and measured daily energy use.
** High-power appliances: Microwave and air-conditioner runtimes are theoretical energy comparisons. The battery and inverter must also support continuous power, startup demands and required discharge current. Sufficient stored energy does not establish electrical compatibility.
Actual runtime may differ because of battery age, temperature, changing loads, inverter idle consumption, discharge-rate effects and manufacturer operating limits. No incoming solar charging is included.
Why Appliance Power Matters
Higher electrical demand reduces battery runtime. For the same usable battery energy, doubling a constant appliance load approximately halves the calculated operating time.
For more accurate planning, measure appliance watt-hours over a representative period and include all simultaneous loads. Use the calculator above to compare different battery capacities, appliance combinations and system-efficiency assumptions.
How Appliance Wattage Affects Solar Battery Runtime
The more power your appliances consume, the faster stored battery energy is used. This comparison shows how different continuous electrical loads affect runtime for the same battery capacity.
Understanding the Runtime Comparison
All five examples use the same 2,000Wh nominal battery, an illustrative 80% depth of discharge, full battery health and 90% inverter efficiency.
Available AC-equivalent energy:
2,000Wh × 0.80 × 0.90 = 1,440Wh
Estimated runtime equals usable energy divided by continuous appliance power. The bar heights are proportional to the calculated runtimes.
Key takeaway: Doubling the continuous electrical load halves the theoretical runtime when all other assumptions remain unchanged.
These are energy-only estimates. Actual operating time depends on battery condition, temperature, conversion losses and equipment limits. High-power loads also require adequate inverter output and battery discharge capability. No incoming solar energy is included.
Solar battery runtime — explained with real numbers
Explore the energy formula, appliance scenarios and model limits. The examples state their assumptions; use actual equipment data when planning backup demand.
The runtime formula
Start here — how to calculate real runtime, and why nameplate capacity is optimistic.
Q1What is the solar battery runtime formula?+
Runtime equals AC-equivalent usable Wh divided by equivalent average AC watts. Simple Mode uses your entered load. Advanced appliance watts are averaged over 24 hours, then AC standby and battery-side idle demand are included. No incoming solar is credited.
Q2Why is “usable” capacity less than what the battery is rated for?+
This tool multiplies nominal energy by health, any enabled cold/discharge-rate factors, DoD and inverter efficiency. Its usable Wh is AC-equivalent delivered energy, not the original nameplate rating. Do not subtract those same losses again from the result.
Q3What is depth of discharge and why does it matter?+
DoD is the fraction of capacity discharged. The calculator presets use 90% for LiFePO4, 85% for NMC and 50% for the lead-acid selections. These are illustrative model choices. Manufacturer limits and cycle life depend on the actual battery and conditions; they are not established by a chemistry label.
Q4Solar battery runtime example for a small backup system+
At 2,000Wh, full/new health, 80% DoD and 90% inverter efficiency with no optional derating, standby or idle draw, usable energy is 1,440Wh. A 200W continuous load gives 7.2 hours. Set Advanced DoD override to 80% to reproduce this; the Simple LiFePO4 preset instead uses 90%.
Appliance runtime examples
Illustrative calculations for entered watts and energy, not appliance performance tests.
Q5How long will a solar battery run a refrigerator?+
Use measured daily energy and check compressor running and startup demands separately. In Advanced Mode, 150W for 8 hours/day gives 1,200Wh/day and a 50W daily average. At 1,440Wh delivered energy this is 1.2 energy-equivalent days. It does not predict a particular compressor schedule or food temperature.
Q6How long will a solar battery run a CPAP machine?+
Use the actual device and accessory power requirements, including any heater or humidifier. At a hypothetical 50W continuous demand and 1,440Wh delivered energy, the energy-only estimate is 28.8 hours. This calculator does not verify a medical-device power supply or backup arrangement; follow the device manufacturer’s requirements.
Q7How long will a solar battery run a space heater?+
At a hypothetical 1,500W continuous load and 1,440Wh delivered energy, runtime is 0.96 hours, or about 58 minutes. Confirm equipment ratings independently. Reducing heater watts does not necessarily reduce the energy needed for the same heating task.
Q8How long will a solar battery run an air conditioner?+
Enter measured electrical demand and realistic usage hours; BTU capacity alone does not establish watts. At a hypothetical 1,000W continuous demand and 1,440Wh delivered energy, runtime is 1.44 hours. This is not a cooling-duration or startup-compatibility prediction.
Q9How long will a solar battery run basic electronics (router, laptop, phone)?+
Add the actual devices and their on-hours. A hypothetical combined 100W continuous demand uses 2,400Wh/day; 1,440Wh delivered energy gives 14.4 hours. Include required adapters, AC standby and inverter idle demand without counting the same loss twice.
Q10How long will a solar battery power a whole house?+
Use your measured or itemized demand and identify which loads need backup. The tool does not supply a universal household consumption value or select a whole-home battery. Runtime is only an energy estimate; simultaneous power, startup, charging and equipment limits need separate checks.
What affects runtime most
The hidden losses that silently eat your real-world runtime.
Q11What affects solar battery runtime the most?+
Capacity, usable fraction, health, average demand and losses all affect the result. Their relative importance depends on the scenario. Compare one input at a time rather than assuming a universal ranking or inferring inverter efficiency from waveform type alone.
Q12How does temperature affect battery runtime?+
Advanced cold mode applies a fixed illustrative loss: 12% for LiFePO4, 20% for NMC and 30% for lead-acid. It applies when checked, regardless of temperature, and is forced on below 40°F. This is not a continuous temperature curve or a permitted operating range. Check actual battery charging and discharge limits separately.
Q13Does Peukert’s law apply to my battery?+
Lead-acid delivered capacity can depend on discharge rate. This tool applies a capped illustrative battery-demand-to-capacity penalty, not a manufacturer Peukert-exponent calculation. It applies no such penalty to lithium presets; that simplification does not establish rate-independent battery performance.
Q14How much energy do parasitic loads eat?+
A hypothetical 10W continuous load uses 240Wh/day. Here AC standby watts receive inverter-efficiency treatment, while inverter idle is battery-side watts. Advanced equivalent AC draw adds idle watts multiplied by efficiency. Do not add idle again if it is already included in your measured conversion-loss assumption.
Q15Does running multiple appliances at once reduce total runtime?+
Total appliance energy depends on watts and on-hours. Advanced Mode averages that energy over 24 hours and does not simulate which appliances overlap. Simultaneous and startup power can still exceed equipment ratings even when the average energy result appears adequate.
Chemistry & runtime differences
How preset assumptions change modeled usable energy; actual products vary.
Q16Why does LiFePO4 run so much longer than lead-acid at the same Wh?+
The presets use different illustrative DoD fractions and capacity adjustments, so modeled usable energy can differ at equal nominal Wh. That does not establish a universal chemistry advantage, cycle life or purchase value. Compare specific products under equivalent test and operating conditions.
Q17Does battery age affect runtime?+
Battery health scales nominal capacity in this model. At otherwise equal assumptions, an 80% health setting gives 80% of the new-battery modeled energy and runtime. The selected fraction is an input assumption, not a diagnosis or an age-to-capacity prediction.
Extending your runtime
Practical ways to get more hours from the bank you already have.
Q18How do I extend my battery runtime without buying more batteries?+
Measure and reduce unnecessary demand or standby use, then compare scenarios. Avoid double counting duty and runtime reductions. Moving loads to solar hours can change actual battery draw, but this battery-only model does not credit that incoming energy. Equipment changes require separate compatibility checks.
Q19How many solar panels do I need to keep the battery charged indefinitely?+
No fixed panel count guarantees indefinite operation. Compare location- and season-specific generation with daily demand, losses, storage and the required recovery period. This runtime calculator includes no solar input. Use Solar Panel Output and full-system planning tools for separate generation scenarios.
Q20How do I calculate the battery size I actually need?+
For an illustrative constant-load case without extra derating or idle draw, nominal Wh = target hours × AC load W ÷ (DoD × inverter efficiency × health). At 400W for 12 hours, 90% DoD, 92% efficiency and new health, this is 5,797Wh. Backup days and reserve assumptions need explicit planning; use the Battery Bank Size Calculator.
Explore your estimated runtime
Compare explicit battery, load and loss assumptions. The result is a planning estimate, not a measurement or an equipment approval.
Related Tools for Battery Performance and Usage
These tools help refine discharge behavior, appliance usage, battery configuration, and wiring considerations without repeating the main next-step links above.
Solar Battery Discharge Calculator
Analyze how your battery drains under different load conditions.
Appliance Runtime Calculator
Estimate how long individual appliances will run on your battery system.
Battery Series Parallel Calculator
Compare nominal voltage, Ah and Wh for complete matching-module groups.
Solar Wire Size Calculator
Explore preliminary voltage-drop and current assumptions; check installation requirements separately.
Battery capacity reference
Usable capacity depends on battery chemistry, discharge rate, temperature and manufacturer limits. See Victron Energy’s battery capacity and Peukert-effect guidance. This estimate does not establish safe continuous discharge or inverter compatibility.
